SOFTPAQ NUMBER:  SP9500
PART NUMBER:  N/A
FILE NAME:  N/A
TITLE:  Compaq Server Support for Microsoft Windows NT 3.51
        (Remote Insight Board Drivers)
VERSION:  1.34 Rev A

LANGUAGE:  Japanese

CATEGORY:  Drivers

DIVISIONS:  Systems

PRODUCTS AFFECTED:  All Compaq Servers

OPERATING SYSTEM:  Microsoft Windows NT Version 3.51(Japanese)

SYSTEM CONFIGURATION:  N/A

PREREQUISITES:  N/A

EFFECTIVE DATE:  January 21, 1999

ELECTRONIC DISTRIBUTION ALLOWED:  Yes

SOFTPAQ UTILITY VERSION:  2.x

SUPERSEDES:  SP8626

DESCRIPTION:  This SoftPaq is for Japanese products, and cannot be 
run in United States mode.  This SoftPaq creates two files -- a description 
file and a self-extracting executable file.  The self-extracting executable 
file contains Compaq Server Support for Microsoft Windows NT 3.51
that supports the following subsystems and features of 
Compaq Servers:

   Compaq Remote Insight Board/PCI Driver
   Compaq Remote Insight Board/PCI WAN Driver
   Compaq Server Support Installation Utility

Enhancements/Fixes:

The release of the Compaq Server Support for Microsoft Windows NT 3.51 
Version 1.34A includes updates to the Compaq Remote Insight Board PCI 
WAN Driver, the Compaq System Management Driver, and the Compaq Server 
Support Setup for Microsoft Windows NT 3.51 program.

Compaq Remote Insight Board Driver(CPQRIB.SYS) 
-	Updated the Compaq Remote Insight Board Driver version from 1.50 
	to 1.51.  Version 1.51 corrects an issue where the previous version 
	of the Compaq Remote Insight Board Driver would not start on a 
	multiprocessor Compaq ProLiant 3000 or 5500 configured as follows: 
	Compaq Remote Insight Board/EISA and system ROM dated later than 3/98.

Compaq Remote Insight Board/PCI WAN Driver(RIBWAN.SYS) 
-	Updated the RIBWAN.INF file to re-enable the Compaq Remote Insight 
	Board/PCI Driver and the Compaq Remote Insight Board/PCI WAN Driver 
	after these drivers are installed and removed using Compaq Server 
	Support Setup for Microsoft Windows NT then reinstalled through the 
	Windows NT Control Panel using the RIBWAN.INF file.
-	Fixed a Compaq Remote Insight Board/PCI WAN routing issue.  In the 
	Compaq Remote Insight Board User Guide, you are asked to perform 
	the "route add A B" command, where A and B are IP addresses.  In 
	previous Compaq SSD for Windows NT 3.51 versions, the packets 
	destined for target A are not routed through the device properly 
	if B is an IP address on one of the Compaq Remote Insight Board/PCI 
	WAN endpoints.  Beginning in Compaq SSD for Windows NT 3.51 Version 
	1.34A, the packets destined for IP address A are properly routed 
	through IP address B, which is the Compaq Remote Insight Board/PCI 
	WAN device.

For details, refer to NTREADME.HLP in the created support files.

HOW TO USE:

1. Download the SoftPaq to a directory on your hard drive and change 
to that directory.  The file that is downloaded is a self-extracting
executable with a filename based on the SoftPaq Number above.

2. From that drive and directory, execute the downloaded file 
and follow the on-screen instructions to unpack the files.
The number of files to be created and total file size is displayed.
You will be given the chance to specify the target directory for 
the files, or default to the download directory.
The following files will be created:
       README.TXT
       RIB.EXE

3. After the files have been created, you may delete the  
self-extracting file downloaded in step 1.

4. From the directory in which the files are created, execute the 
self-extracting executable:
       RIB.EXE [ENTER]

5. Follow the instructions on the screen to extract (unzip) the support 
software files to a folder on your hard drive and run the program 
SETUP.EXE to install the software.

Copyright 1999, Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.