SOFTPAQ NUMBER:  SP7650
PART NUMBER:  N/A
FILE NAME:  N/A
TITLE:  Compaq Netelligent 56K ISA/Internal Fax Modem Firmware Upgrade 
VERSION:  1.12 
LANGUAGE:  English

CATEGORY:  ROMPaq

DIVISIONS:  Comm-Network

PRODUCTS AFFECTED:  Compaq Netelligent 56K ISA Fax Modem,
                    Compaq Netelligent 56K Internal Fax Modem 
                    (firmware version 0.519 and 1.0)
                    
OPERATING SYSTEM:  Microsoft Windows 95,
                   Microsoft Windows 98,
                   Microsoft Windows NT 4.0

SYSTEM CONFIGURATION:  IBM Compatible 486DX2/66 or greater with 4-MB 
system RAM, at least 35MB of free hard disk space, and an empty ISA slot

EFFECTIVE DATE:  July 2, 1998 

ELECTRONIC DISTRIBUTION ALLOWED:  Yes

SOFTPAQ UTILITY VERSION:  2.x

SUPERSEDES:  SP5014

DESCRIPTION:  Creates a diskette used to upgrade the firmware to 
version 1.12 for a Compaq Netelligent 56K ISA Fax Modem or Compaq 
Netelligent 56K Internal Fax Modem with firmware version 0.519 or 1.0.  
This is the same version that was included in SoftPaq SP5014, with the 
exception of added installation instructions for Windows 98.  

Enhancements/Fixes:
 - Added installation instructions for Microsoft Windows 98

This version addresses the following problems that existed in version 1.0:

- V.8bis tone detection in presence of calling tone for countries with 
  calling tone on by default
- CIS table not available after flash recovery mode
- NVM recall, missing INX
- TIES sequence and DMON timer used the same system flag
- Incorrect CIS info LP model
- ATI2 reports ERROR if ConfigurACE is used and it is flash downloaded 
- DCD on before CONNECT message DP model
- CID does not work when waking up 
- Last field in +MS command not stored in NVM 
- V.8bis tone could not be detected during calling tone 
- AT&V1 speed incorrect for 7200-14400 
- Modem goes offhook when waking up on a command that results in ERROR 
- AT#VTS locks up modem in FDSP 
- Lockup after V8 CI 
- AT+A8E? returns incorrect settings 
- V.21 and V.23 modes do not display a connect message 
- W-Class code works with US devices 
- Offhook after AT-SMS=1 
- Incorrect #SPK default parameters 
- V.8bis CRe at incorrect level 
- Playback to speaker (#VLS=1) is noisy 
- A-law vs. U-law aggressiveness unequal
- V.80 and VRPI modes too aggressive
- Enable Retrain during handshake
- Clear TX rate mask when fallback to V.34
- Cannot do K56flex after analog loopback
- Cannot fall back to V.32bis when calling a V.FC modem
- LAPM forced through V.8bis for V1.1 K56flex
- Call Waiting detection added with 16>=S210<255
- Add ability to fallback to V.34 during retain
- NVM stored dialstrings shortened to 34 characters
- BI not set when Break is received DP model 

HOW TO USE:

1. Obtain a formatted 1.44-MB diskette.

2. Download the SoftPaq to a directory on your hard drive and change 
to that directory.  The file that is downloaded is an executable with 
a filename based on the SoftPaq Number above.

3. From that drive and directory, execute the downloaded file 
and follow the on-screen instructions.  You will be prompted to 
insert the formatted diskette in a drive to create the diskette.

4. After the diskette has been created, you may delete the  
SoftPaq file downloaded in step 2.

5. Refer to the README.TXT file on the diskette for upgrade instructions.

Copyright 1998, Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered 
trademarks of their respective companies