SOFTPAQ NUMBER:  SP7340
PART NUMBER:  312687-29F
FILE NAME:  N/A
TITLE:  PC Diagnostics and Computer Setup/VP
VERSION:  10.27 Rev C for PC Diagnostics   
	  1.75 Rev B for Computer Setup/VP
LANGUAGE:  Japanese

CATEGORY:  Diagnostics-Setup

DIVISION:  Desktops

PRODUCTS AFFECTED:  Compaq Deskpro 4000 Series, Deskpro 6000 Series,  
Deskpro 2000 Series models with an MMX processor, Deskpro EP Series
Despro SB Series, Deskpro EN Series

OPERATING SYSTEM:  N/A

SYSTEM CONFIGURATION:  N/A

PREREQUISITES:  N/A

EFFECTIVE DATE:  June 9, 1998

ELECTRONIC DISTRIBUTION ALLOWED:  Yes

SOFTPAQ UTILITY VERSION:  3.1

SUPERSEDES:  SP6478

DESCRIPTION:
Creates four diskettes:
- Two (2) diskette for Personal Computer Diagnostics Version 10.27 Rev C
- Two (2) diskettes for Computer Setup/VP Version 1.75 Rev B

For all products except the Deskpro EP Series, Computer Setup and PC Diagnostics
are both pre-installed on the Diagnostics Partition.  The diskettes in this
SoftPaq can be used to update these utilities on the Diagnostics Partition or
to restore them if the Diagnostics Partition has been destroyed.   Both utilities
can be run by pressing F10 during power-up or reboot when prompted in the lower 
right corner of the screen on some models or when the cursor jumps to the 
upper right corner of the screen on other models.  Or they can be run 
directly from these diskettes.

NOTE: For the Deskpro EP Series only, Computer Setup/VP and Personal 
Computer Diagnostics must be run from diskette.

Computer Setup/VP allows the user to configure security and power 
management settings as well as system resources (DMA, IRQ, I/O Ports, 
and Memory).  It is specific to the Deskpro models mentioned above.

Personal Computer Diagnostics contains programs that can test and 
inspect the state of the computer and its devices.  It is used with the 
Deskpro models mentioned above, as well as other Compaq desktops and 
portables.

Enhancements/Fixes:
 - Updated Personal Computer Diagnostics to Rev C
 
HOW TO USE:

1. Obtain four (4) formatted 1.44MB diskettes and place the first one
in one of your diskette drives.

2. Download the SoftPaq to a directory on your hard drive.
The file downloaded is a self-extracting executable with a filename 
based on the SoftPaq Number above.

3. Execute the downloaded file and follow the on-screen instructions. 
Entering "Y" to confirm the unpacking of files creates a new directory 
folder in the download directory.  All files are unpacked into this 
newly created directory.

4. To create the (4) diskettes run the MAKEDISK.BAT file and follow
the prompts.

You will be prompted to enter the additional diskettes.  
Label them as follows:
First Diskette -- Personal Computer Diagnostics Version 10.27 Rev C "TEST" (Disk 1 of 2)
Second Diskette -- Personal Computer Diagnostics Version 10.27 Rev C "INSPECT" (Disk 2 of 2)
Third Diskette -- Computer Setup/VP Version 1.75 Rev B (Disk 1 of 2)
Fourth Diskette -- Computer Setup/VP Version 1.75 Rev B (Disk 2 of 2)

5. After the diskettes are created, you may delete the file downloaded
in step 2 if you wish.

IMPORTANT: If installing Computer Setup/VP to a new unpartitioned hard 
drive, boot from the Diagnostics diskette (First diskette) and follow the 
prompts to create a diagnostics partition.  You will be prompted to insert 
the Setup diskettes.

6. To install or upgrade Computer Setup/VP on the Diagnostics Partition, 
or to run it directly from the diskettes, boot from the first Setup/VP diskette
(third diskette created) and follow the prompts.

7. To install or upgrade Personal Computer Diagnostics on the Diagnostics 
Partition, boot from the Diagnostics diskette (first diskette) .  From the 
"Manage Diagnostics Partition" menu, select "Create" or "Update" partition 
and follow the prompts.

Copyright 1997, 1998 Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies