SOFTPAQ NUMBER:  SP5690
PART NUMBER:  N/A
FILE NAME:  N/A
TITLE:  Computer Setup/VP and PC Diagnostics 
VERSION:  1.73 Rev A for Computer Setup/VP
          10.23 Rev C for PC Diagnostics 
LANGUAGE:  Finnish

CATEGORY:  Desktops/Diagnostics-Setup

PRODUCTS AFFECTED:  Deskpro 4000 Series, Deskpro 6000 Series, and 
Deskpro 2000 models with an MMX processor

OPERATING SYSTEM:  N/A

SYSTEM CONFIGURATION:  N/A

EFFECTIVE DATE:  16 FEB 1998

ELECTRONIC DISTRIBUTION ALLOWED:  Yes

SOFTPAQ UTILITY VERSION:  3.1

SUPERSEDES:  SP5212

DESCRIPTION:
Creates three diskettes:
- One (1) diskette for Personal Computer Diagnostics Version 10.23 Rev C
- Two (2) diskettes for Computer Setup/VP Version 1.73 Rev A 
These related utilities were formerly in two separate SoftPaqs.

Computer Setup and PC Diagnostics are both pre-installed on the 
Diagnostics Partition.  The diskettes in this SoftPaq can be used to 
update these utilities on the Diagnostics Partition or to restore them 
if the Diagnostics Partition has been destroyed.   Both utilities can be 
run by pressing F10 during power-up or reboot when prompted in the lower 
right corner of the screen on some models or when the cursor jumps to the 
upper right corner of the screen on other models.  Or they can be run 
directly from these diskettes.  

Computer Setup/VP allows the user to configure security and power 
management settings as well as system resources (DMA, IRQ, I/O Ports, 
and Memory).  It is specific to the Deskpro models mentioned above.

Personal Computer Diagnostics contains programs that can test and 
inspect the state of the computer and its devices.  It is used with the 
Deskpro models mentioned above, as well as other Compaq desktops and 
portables.

Enhancements/Fixes:
  - Personal Computer Diagnostics was updated to add support for the new 
    node address range for Compaq Network Interface Controllers.
  - Computer Setup/VP remains unchanged at the same version as in the
    superseded SoftPaq.

HOW TO USE:

1. Obtain three (3) formatted 1.44MB diskettes and place the first one 
in one of your diskette drives.

2. Download the SoftPaq to a directory on your hard drive.
The file downloaded is a self-extracting executable with a filename 
based on the SoftPaq Number above.

3. Execute the downloaded file and follow the on-screen instructions. 
Entering "Y" to confirm the unpacking of files creates a new directory 
folder in the download directory.  All files are unpacked into this 
newly created directory.

4. To create the three diskettes run the "MAKEDISK.BAT" file and follow
the prompts.

You will be prompted to enter these diskettes.
Label them as follows:
First Diskette -- Personal Computer Diagnostics Version 10.23 Rev C
Second Diskette -- Computer Setup/VP Version 1.73 Rev A (Disk 1 of 2)
Third Diskette -- Computer Setup/VP Version 1.73 Rev A (Disk 2 of 2)

5. After the diskettes are created, you may delete the files downloaded
in step 2 if you wish.

IMPORTANT: If installing Computer Setup/VP to a new unpartitioned hard 
drive, boot from the Diagnostics diskette (first diskette) and follow the 
prompts to create a diagnostics partition.  You will be prompted to insert 
the Setup diskettes.

6. To install or upgrade Computer Setup/VP on the Diagnostics Partition, 
or to run it directly from the diskettes, boot from the first Setup/VP 
diskette (second diskette created) and follow the prompts.

7. To install or upgrade Personal Computer Diagnostics on the Diagnostics 
Partition, boot from the Diagnostics diskette (first diskette) .  From the 
"Manage Diagnostics Partition" menu, select "Create" or "Update" partition 
and follow the prompts.

Copyright 1998, Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies