SOFTPAQ NUMBER:  SP5050
PART NUMBER:  N/A
FILE NAME:  N/A
TITLE:  Compaq Support Software for Microsoft Windows NT 3.51 
        (Servers)
VERSION:  1.26 Rev A
LANGUAGE:  English

CATEGORY:  Systems/Drivers

PRODUCTS AFFECTED:  Compaq ProLiant and ProSignia Servers

OPERATING SYSTEM:  Microsoft Windows NT 3.51

SYSTEM CONFIGURATION:  N/A

EFFECTIVE DATE:  17 November 1997

SUPERSEDES:  SP4334

DESCRIPTION:  This SoftPaq creates two files -- a description file and a
self-extracting executable file.  The self-extracting executable file 
contains Compaq Support Software for Microsoft Windows NT 3.51 
that supports the following subsystems and features of 
Compaq Servers:
 
   Compaq Integrated Management Display Utility 
   Compaq Recovery Server, Standby Agent with SMART-2 support 
   Compaq Recovery Server, Online Agent with SMART-2 support 
   Compaq Remote Insight Board driver 
   Compaq Remote Insight Board WAN driver 
   Compaq PCI Hot Plug Utility 
   ProLiant Storage System 
   System Management/Health driver 
   NetFlex-3/Compaq Netelligent 10/100 TX Embedded UTP/Coax network adapter
   NetFlex-3/Compaq Netelligent 10/100 TX Embedded UTP/Coax network 
      adapter monitoring, configuration, and duplex utility 
   Compaq 10T PCI UTP and 10/100 TX PCI UTP 
   IDA/IDA-2 disk controller 
   SMART/SMART-2 array controller 
   32-Bit SCSI-2 Family of controllers 
   Compaq Support Software diskette Installation utility 

Enhancements/Fixes:

For details, refer to NTREADME.HLP in the created support files.

This version primarily supports the Compaq Dual Channel Wide-Ultra 
SCSI-3 Controller and the Compaq ProLiant Storage System/U.  It has 
been tested with and supports NT Server Enterprise Edition.

Compaq Dual Channel Wide-Ultra SCSI-3 Controller 

  This controller was designed primarily as a complimentary controller for 
  high end tape solutions, like Compaq?s DLT Tape Array II and DLT Libraries; 
  it provides support for the maximum number of devices possible while only 
  taking up a single PCI slot.  It delivers exceptional system performance 
  along with two separate SCSI-3 channels.

Compaq ProLiant Storage System/U

  The Compaq ProLiant Storage System/U is Compaq's latest edition to the 
  ProLiant Storage System family.  The ProLiant Storage System/U is defined 
  as a disk storage box replacement for the original ProLiant Storage System.  
  The difference between ProLiant Storage System and ProLiant Storage System/U 
  is that this storage box supports SCSI Ultra speeds negotiation and the new 
  Ultra speed disk drives. 

Compaq System Management Driver (SYSMGMT.SYS)

  Changed the policy for stopping at the F1 prompt for systems equipped with 
  the Integrated Management Log.  These systems will no longer stop at the F1 
  prompt on the next boot after the system encounters one or more of the 
  following critical errors:
   - Fan failure
   - System overheating
   - Power supply failure
   - Processor power module failure
   - Processor failure

  Systems not equipped with the Integrated Management Log will still stop at the 
  F1 prompt after encountering these errors.
 
  Updated the severity of error messages sent to the Windows NT Event Viewer to 
  match the severity of the corresponding error messages sent to the Integrated 
  Management Log.  The updated messages are used for reporting:
   - Fan failure
   - System overheating
   - Processor failure
   - Correctable memory errors
   - Fan removal
   - Power supply removal
   - Power supply failure
   - AC line problems
   - Power supply overload

  Error messages placed in the NT Event Viewer by a previous version of the Compaq 
  System Management driver will not be updated.
  
  Corrected reporting of fan failure on the Compaq ProLiant 6500 during the 
  hot-plug fan redundancy check, which is performed once a day.  This check involves 
  briefly running the secondary fans, if installed, to ensure that they will operate 
  in the event of the failure of a primary fan.  A fan could be improperly reported 
  as failed after the check is complete.
  
  Corrected logging of Intelligent Power Supply fan failures.  These failures were 
  improperly reported as AC line under-voltage errors.
  
  Corrected logging of Intelligent Power Supply overload conditions to report the 
  voltage of the overloaded voltage channel.
  
  Corrected logging of the physical PCI slot number after a Non-Maskable Interrupt 
  (NMI) caused by a parity error on the PCI bus.  The physical slot number was 
  improperly reported as unknown.

  Corrected a problem with using the wrong capacity for Intelligent Power Supplies 
  operating from a 220V AC line.  The capacity was incorrectly set to 500W, which 
  is appropriate for 110V operation, instead of the proper 750W.  As a result, a 
  heavily loaded system operating from a 220V line could be incorrectly reported 
  as having a non-redundant power subsystem.

  Added an enhancement for the Compaq ProSignia 200, allowing the system to 
  determine which pair of ECC memory modules failed.  The new event log message 
  that you may receive is "The Compaq System Management Driver has determined that 
  DIMM pair #1 has exceeded its threshold of correctable errors.  Please contact 
  your Compaq service representative."

HOW TO USE:

1. Download the SoftPaq to a directory on your hard drive and change 
to that directory.  The file that is downloaded is a self-extracting
executable with a filename based on the SoftPaq Number above.

2. From that drive and directory, execute the downloaded file 
and follow the on-screen instructions to unpack the files.
The number of files to be created and total file size is displayed.
You will be given the chance to specify the target directory for 
the files, or default to the download directory.
The following files will be created:
       README.TXT
       SRVR.EXE

3. After the files have been created, you may delete the  
self-extracting file downloaded in step 1.

4. From the directory in which the files are created, execute the 
self-extracting executable:
       SRVR.EXE [ENTER]

5. Follow the instructions on the screen to extract (unzip) the support 
software files to a folder on your hard drive and run the program 
SETUP.EXE to install the software.

Copyright 1997, Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.