SOFTPAQ NUMBER:  SP14938
PART NUMBER:  N/A
FILE NAME:  N/A
TITLE:  Intel 815 Chipset Display Driver for OS/2
VERSION:  1.00 Revision A 
LANGUAGE:  US English

CATEGORY: Drivers

DIVISIONS: Commercial Desktops

PRODUCTS AFFECTED: 
Deskpro EN Series:     P933, P866, P800, P733, P667, C600
Deskpro EN Series SFF: P933 (SFF), P866 (SFF), P800 (SFF), P733 (SFF), 
                       P667 (SFF), C600 (SFF)
Evo D300 Small Form Factor: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset
Evo D500 Desktop: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset
Evo D300 Desktop: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset
Evo D500 Convertible Minitower: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset
Evo D300 Convertible Minitower: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset
Evo D500 Small Form Factor: 
         Pentium 4 2.0G 845 Chipset,
         Pentium 4 1.9G 845 Chipset,
         Pentium 4 1.8G 845 Chipset,
         Pentium 4 1.7G 845 Chipset,
         Pentium 4 1.6G 845 Chipset,
         Pentium 4 1.5G 845 Chipset


OPERATING SYSTEM: IBM OS/2 Warp 3.0
                  IBM OS/2 Warp 4.0

SYSTEM CONFIGURATION:  N/A

PREREQUISITES: Requires OS/2 Warp FixPak 2 or above

EFFECTIVE DATE: July 17, 2000

ELECTRONIC DISTRIBUTION ALLOWED: Yes

SOFTPAQ UTILITY VERSION: 3.0

SUPERSEDES: N/A

DESCRIPTION:  Contains the IBM OS/2 Warp 3.0/4.0 graphics driver for the 
Intel 3D Direct Graphics 82815 chipset that ships with the Deskpro EN Series 
products listed above.

HOW TO USE:

1. Download the SoftPaq to a directory on your hard drive.
The file downloaded is a self-extracting executable with a filename
based on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions.

3. After the files have been unpacked, you may delete the self-extracting
file downloaded in step 1.

4. To install: Check the System Requirements.  OS/2 must be fully
installed and running on the system prior to running this
software. The system must be in VGA mode. If installing additional
fixpacks, do so while the system is in VGA mode. For instructions
on setting the desktop in VGA mode, refer to "Deinstalling the
software" section. All WinOS2 sessions must be closed prior to
installing this driver.

a.  Insert the Intel GRADD driver diskette into drive A (or any other diskette
    drive).
b.  Open an OS/2 full-screen or OS/2 window session.At the OS/2 command prompt,
    change to A: drive.
c.  At the OS/2 command prompt, type the following command to copy all
    necessary files to the OS/2 drive:

    SETUP <SrcPath> <BootDrive> [/u]

          <SrcPath> is the diskette drive

          <BootDrive> is the drive where OS/2 is installed.

          [/u] is optional and is used to indicate unattended install
               such as for CID installations. A CID response file is
               not required.

    Then press Enter.
    A number of system files will be transferred if the ones found on the
    system are older. When a popup asking for Monitor configuration choice
    pops up, accept "Use monitor defaults" choice.
    The installation will then blank the screen while testing VESA modes and
    if successful, it will transfer driver files.               
d.  When prompted to do so, remove the diskette from drive A, perform a
    shutdown, and then restart your computer.
e.  When the system reboots, do the following:
    a.  Open the OS/2 System folder.
    b.  Open the System Setup folder.
    c.  Open the System object.
    d.  When the Settings notebook appears, select the Screen tab.
    e.  Select a resolution from the page 1.
    f.  Select a monitor from page 2.
          g.  Select refresh setting from the page 1 of the Screen tab. 
    h.  Close the Settings notebook.
    i.  The selected resolution will be in effect upon the next boot.


5. To create (optional) installation (or other deliverable) diskette(s) 
run MAKEDISK.BAT and follow the on-screen instructions. 
MAKEDISK.BAT is included only if installation diskette(s) creation is an option.

6. After the installation is completed, you may delete the directory
created in step 2 if you wish.

   Copyright 1995-2000, Compaq Computer Corporation. All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.