SOFTPAQ NUMBER:  SP10369
PART NUMBER:  183239-697,275078-697
FILE NAME:  N/A
TITLE:  Computer Setup/VP
VERSION:  1.75 Rev C
LANGUAGE:  Japanese

CATEGORY:  Diagnostics-Setup

DIVISION:  Desktops

PRODUCTS AFFECTED:
     Deskpro 4000 Series: 5166MMX,5200MMX,5233MMX,6233MMX,6266MMX,6300MMX
     Deskpro 6000 Series: 6233MMX,6233X,6266MMX,6266X,6300MMX
     Deskpro 2000 Series: 5166MMX,5200MMX,5233MMX,6233MMX,6266MMX,6300MMX
     Deskpro EP Series: 6266,6266C,6300,6300A,6333,6333C,6350,6400,6400C,6450,
                        6450+,6500,P550,P600,P650,P700
     Deskpro SB Series: 6266,6300,6333,6350,6400
     Deskpro EN Series: 6266,6300,6300A,6300C,6333,6333C,6350,6400,6400C,6450,
                        6450+,6500,P550,P600,P650,P667,P700
     Deskpro EN Series SFF: 6300,6300A,6300C,6333,6333C,6350,6400,6450,6450+,
                            6500,NetPC 6300,NetPC 6400,P550,P600,P650,P700

OPERATING SYSTEM:  N/A

SYSTEM CONFIGURATION:  N/A

PREREQUISITES:  N/A

EFFECTIVE DATE:  April 6, 2001

ELECTRONIC DISTRIBUTION ALLOWED:  Yes

SOFTPAQ UTILITY VERSION:  3.1

SUPERSEDES:  SP7340

DESCRIPTION:

For all products except the Deskpro EP/EN Series, 
Computer Setup are both pre-installed on the Diagnostics Partition.
The diskettes in this SoftPaq can be used to update the utility on the 
Diagnostics Partition or to restore them if the Diagnostics Partition has been
destroyed.   The utility can be run by pressing F10 during power-up or 
reboot when prompted in the lower right corner of the screen on some models or 
when the cursor jumps to the upper right corner of the screen on other models.
Or they can be run directly from these diskettes.

NOTE: For the Deskpro EP/EN Series, Computer Setup/VP must be run from diskette.

Computer Setup/VP allows the user to configure security and power 
management settings as well as system resources (DMA, IRQ, I/O Ports, 
and Memory).  It is specific to the Deskpro models mentioned above.

HOW TO USE:

1. Obtain two (2) formatted 1.44MB diskettes and place the first one
in one of your diskette drives.

2. Download the SoftPaq to a directory on your hard drive.
The file downloaded is a self-extracting executable with a filename 
based on the SoftPaq Number above.

3. Execute the downloaded file and follow the on-screen instructions. 
Entering "Y" to confirm the unpacking of files creates a new directory 
folder in the download directory.  All files are unpacked into this 
newly created directory.

4. To create the (2) diskettes run the MAKEDISK.BAT file and follow
the prompts.

You will be prompted to enter the additional diskettes.  
Label them as follows:
First Diskette -- Computer Setup/VP Version 1.75 Rev C (Disk 1 of 2)
Second Diskette -- Computer Setup/VP Version 1.75 Rev C (Disk 2 of 2)

5. After the diskettes are created, you may delete the file downloaded
in step 2 if you wish.

IMPORTANT: If installing Computer Setup/VP to a new unpartitioned hard 
drive, boot from the Personal Computer Diagnostics diskette and follow the 
prompts to create a diagnostics partition.  You will be prompted to insert 
the Setup diskettes.

6. To install or upgrade Computer Setup/VP on the Diagnostics Partition, 
or to run it directly from the diskettes, boot from the first Setup/VP diskette
(first diskette created) and follow the prompts.


Copyright 1997, 1999 Compaq Computer Corporation.  All rights reserved.

Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies