File Name:  1232X21.EXE
Title:  Compaq PageMarq Lotus 1-2-3 for DOS Release 2.3 & 2.4 Text and
        WYSIWYG Drivers
Driver Version:  2.1
Instructions Version:  09/12/94

CATEGORY:  Driver

EFFECTIVE DATE:  02/11/94

PRODUCTS AFFECTED:  PageMarq 15 and PageMarq 20 laser printers

OPERATING SYSTEM:  MS-DOS

SYSTEM CONFIGURATION:  Lotus 1-2-3 for DOS Release 2.3 & 2.4

SUPERSEDES:  SP0487

DESCRIPTION:

This release contains the printer drivers for the Compaq PageMarq 15 and 20
laser printers using Lotus 1-2-3 for DOS Release 2.3 & 2.4 Text and WYSIWYG.
The Softpaq contains a self-extracting archive named 1232X21.EXE.  To use the
driver, you must first build the update diskette using the following steps:

1. Execute the Softpaq in any empty directory.
2. Make that directory current.
3. Pre-format (1) 1.44MB diskette.
4. Execute 1232X21.EXE A: or 1232X21.EXE B:

NOTE: If you require a 1.2MB diskette, all the files can be copied from the
      update diskette with the "XCOPY /S" command.


TABLE OF CONTENTS:
========================================================
I.....General Information about PageMarq WYSIWYG drivers
II....Installation Instructions for Update Disk
III...Printing The SP0930.DOC File
========================================================


===============================================================
(I) GENERAL INFORMATION ABOUT PAGEMARQ WYSIWYG DRIVERS
===============================================================
These drivers provide enhanced output for WYSIWYG graphics printing
(:Print) in 1-2-3 for DOS Release 2.3 and 2.4.  The drivers enhance
printing with the :Print menu; they do not work with 1-2-3 text
printing (the /Print menu) or with PrintGraph.


PAPER TRAY HANDLING

Paper tray selection works using the principle of tray PRIORITIES.
If several trays contain like sized paper, they will be searched for a
non-empty tray in an order which depends on the tray selected in the
WYSIWYG configuration (:Print Config Bin).  The tray selections work as
follows:

        TRAY            ORDER IN WHICH TRAYS ARE SEARCHED

        Upper           Upper Lower MPF

        Lower           Lower Upper MPF

        Single          MPF only (uses MPF irrespective of page size)

        Manual          Manual Feed only (should be used only if no MPF
                        is installed)

        Reset           Uses the printer control panel default


======================================================
(II) INSTALLATION NOTES FOR UPDATE DISK
======================================================

NOTE: If you run 1-2-3 from a network drive, your network
administrator must install the Update on your server.  Network
administrators need full access rights to install the Update.
The installation procedure below is the same for stand-alone
users and for network administrators.

To use the Update Disk, you must complete these steps:

1.  Insert the Update Disk in drive A: (or B:)

2.  At the operating system prompt, type A: (or B:) and press
    ENTER to make A: (or B:) the current drive.

NOTE FOR NETWORK ADMINISTRATORS:  Make sure you have full access rights
to the 1-2-3 directory and the WYSIWYG subdirectory before you proceed.

3.  At the prompt, type UPDATE followed by a space and the path of your
    Release 2.4 or 2.3 directory, and then press ENTER.  For example, if
    you have Release 2.4 and your directory is c:\123r24, you would
    type UPDATE c:\123r24 and then press ENTER.  When the Update is
    complete, the following message appears: "1-2-3 Update files have
    been installed.  To take advantage of the new printer drivers,
    you must now run the 1-2-3 Install program."

4.  To start Install, refer to the instructions on screen or follow the
    instructions in Chapter 5 of Getting Started (if you have Release
    2.4) or Chapter 3 of Getting Started (if you have Release 2.3).

    Then select the following:

    Change Selected Equipment

    Add New Drivers to the Library 

    Modify the Current Driver Set

    Text Printer.  Select your printer model

    Graphics Printer.  Select your printer model

    Save the Current Driver Set

    Yes when Install asks if you want to generate fonts.

    If you have multiple driver sets, you must recreate each driver
    set using the Change Selected Equipment option.

5.  After you end Install, perform the steps in section II
    (1-2-3 FOR DOS APPLICATION NOTES) to print with your new
    printer drivers.


===================================================================
(III) PRINTING THE SP0930.DOC FILE
===================================================================

NOTE:  PRINTING SP0930.DOC TO A LOCALLY CONNECTED PRINTER

       1. Make the drive that contains the Update Disk current.
       2. At the DOS prompt, enter the following command:

          PRINT SP0930.DOC PRN


          (Where PRN represents the port you print to
          for example LPT1, LPT2, LPT3, or PRN)


For more information on printing a file from DOS, please consult your
DOS manual.



NOTE:  PRINTING SP0930.DOC TO A NETWORK PRINTER

       1. Make the drive that contains the Update Disk current.
       2. At the DOS prompt, enter the following command:

          COPY SP0930.DOC LPTX

          (Where X  represents the port you print to
          for example LPT1, LPT2, LPT3, or LPT4)

For more information on printing a file from DOS, please consult your
DOS manual.  For more information on determining your network printer port,
please contact your network administrator.

==================================================================
The Update contained on this diskette is licensed by Lotus Development
Corporation, solely for the use by Licensed Users of 1-2-3 for DOS
Releases 2.3 and 2.4.

(C)opyright 1992, 1993 Lotus Development Corporation.  All Rights Reserved.

LOTUS DEVELOPMENT CORPORATION MAKES NO WARRANTIES,
EITHER EXPRESS OR IMPLIED REGARDING THE
ENCLOSED, INCLUDING MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.  THE EXCLUSION OF IMPLIED
WARRANTIES IS NOT PERMITTED BY SOME STATES. THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU.  THERE MAY BE OTHER
RIGHTS THAT YOU MAY HAVE WHICH VARY FROM STATE TO STATE.

LOTUS DEVELOPMENT CORPORATION EXCLUDES ANY WARRANTY
COVERAGE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU.

Lotus (R) and 1-2-3 (R) are registered trademarks of Lotus Development
Corporation.